ECET 405 ECET405 ECET/405 ENTIRE COURSE HELP – DEVRY UNIVERSITY

Description

ECET 405 ECET405 ECET/405 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECET 405 Week 1 Chapter 2 Homework

ECET 405 Week 1 iLab

ECET 405 Week 2 Chapter 2 Homework

ECET 405 Week 2 iLab

ECET 405 Week 3 Chapter 4 Homework and Chapter 5

ECET 405 Week 3 iLab

ECET 405 Week 4 Chapter 7 Homework

ECET 405 Week 4 iLab Hardwiring your PLC

ECET 405 Week 5 Homework

ECET 405 Week 5 iLab Traffic Lights

ECET 405 Week 6 Homework

ECET 405 Week 6 iLab Project Design

ECET 405 Week 7 iLab Project Design II

ECET 405 ECET405 ECET/405 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECET 405 Week 1 iLab

A Control Problem with Multiple Inputs and Outputs

1.Complete Table 1 below per lab instructions

2.Take a digital photo of your completed circuit and insert it below.

3. In a paragraph write your comments on any wiring issues or challenges that you encountered. How did you troubleshoot or fix the problem (if any)? Was there any flickering of the LEDs when the motor was running or stopped? If so, how would you fix the problem?

4. Submit the completed worksheet to week-1 Lab Dropbox.

ECET 405 ECET405 ECET/405 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECET 405 Week 2 Chapter 2 Homework

Chapter 2 Homework

1)A discrete 120 V ac output module is to be used to control a 230 V dc solenoid valve. Draw a diagram showing how this could be accomplished using an interposing relay.

2)Assume a thermocouple generates a linear voltage of from 20 mV to 50 mV when the temperature changes from 750°F to 1250°F. How much voltage will be generated when the temperature of the thermocouple is at 1000°F?

5)Assume the triac of an ac output module fails in the shorted state. How would this affect the device connected to this output?

ECET 405 ECET405 ECET/405 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECET 405 Week 2 iLab

1.Per step 6 of Lab 2 instructions, turn on the power supply and touch the loose end of the red wire shown in Figure 7 to input terminals X0, X1, X2, X3, X4, X5, X6, and X7. Indicate which of LEDs marked X0 to X7 will turn on.

1.Explain why some of the input LEDs do not turn on as you touch the loose red wire to some of the input terminals of the PLC.

2.What needs to be done to enable those LEDs that did not turn on, to turn on as you touch the loose end of the red wire to corresponding input terminals?

3.Explain what you need to do to turn on LEDs X0 and X5 at the same time?

4.Explain what you need to do to turn on LEDs X0, X2, X4, and X6 at the same time?

5.For the software part of the lab answer the following questions:

6.Describe the operation of each instruction in each rung:

7. Describe how you would modify the program so that when overheating occurs for the first time, the entire process stops

ECET 405 ECET405 ECET/405 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECET 405 Week 3 iLab

1. Once you have completed step 6 of lab 3, Print Screen your ladder logic program that contains your last name on rung 3 and paste it below.

2. Once you have completed step 12 of lab3, Print-screen the ladder logic program you created and paste it below. Then submit the worksheet to week 3 Dropbox.