ECT 122 ECT122 ECT/122 ENTIRE COURSE HELP – DEVRY UNIVERSITY

Description

ECT 122 ECT122 ECT/122 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECT 122 Week 1 iLab 2

ECT 122 Week 2 iLab 1 Ohms Law

ECT 122 Week 2 iLab 2

ECT 122 Week 2 iLab 3

ECT 122 Week 3 iLab 1

ECT 122 Week 3 iLab 2

ECT 122 Week 3 iLab 3

ECT 122 Week 4 Homework Practice Problems

ECT 122 Week 4 iLab 1

ECT 122 Week 4 iLab 2

ECT 122 Week 4 iLab 3

ECT 122 Week 5 Homework Practice Problems

ECT 122 Week 5 iLab 2

ECT 122 Week 5 iLab 3

ECT 122 Week 6 iLab 1

ECT 122 Week 6 iLab 2

ECT 122 Week 7 iLab 1

ECT 122 Week 7 iLab 2

ECT 122 Week 7 iLab 3

ECT 122 Week 6 Quiz

ECT 122 ECT122 ECT/122 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECT 122 Week 6 Quiz

1. (TCO 3) For the circuit below, what will XMM6 read if the switch is open?

XMM1 is measuring current and the other DMMs are measuring voltage

2. (TCO 3) For the circuit below, calculate the resistance from A to B.

3. (TCO 4) For the circuit below, how much current is leaving the node connecting V1 and R1.

4. (TCO 5) Determine the current through R2 in the circuit below.

5. (TCO 4) Determine the power disappointed by R3 in the circuit below

6. (TCO 5) Determine the power dissipated in R1 in the circuit below.

7. (TCO 5) For the circuit below, calculate the current through the 2 kΩ resistor

8. (TCO 6) I1 is 2mA; I2 is 1mA. What is voltage Vx and resistance R5?

9. (TCO 8) For the circuit below, calculate all the voltages and currents. Then shown the fault voltages, determine which component is at fault and if it is an open or a short. If Vs = 6V

ECT 122 ECT122 ECT/122 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECT 122 Week 1 iLab 2

ECT 122 Week 1 iLab #2

Part 1

1.Calculate the conductance of the following resistors:

Note: don’t forget the units!

2.Calculate the resistance of a circuit that has the following conductance of

3.Describe a Conductor.

4. Give two examples of Insulators.

5.What is a Semiconductor and give an example?

Part 2

1.Using the Internet, search for a schematic symbol for a dc battery and paste it below or draw the symbol for a battery and label its terminals.

2. What is the difference between a battery and a power supply?

3. Use Multisim to create a schematic containing the following components

ECT 122 ECT122 ECT/122 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECT 122 Week 2 iLab 3

ECT 122 Week 2 iLab #3

Part 1

Parts:

Breadboard

DC Power Supply

Hand Held DMM

Test leads

Wire

56kΩ resistor

1. Given the circuit below, use Ohm’s law to determine the total current in the circuit and the voltage across the resistor.

ECT 122 ECT122 ECT/122 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECT 122 Week 3 iLab 1

1.Identify the type of the following circuits as either serial or parallel.

2.List four characteristics of a series circuit.

3.Calculate the total resistance in the circuit below. Show the formula used.

4.Download the Multisim file “Series1” from Doc Sharing, Week 3. Run the simulation and verify the simulated results are the same as the calculated values. Were the values the same? Yes/No. If No, why?

5.Construct the circuit above on the breadboard. Have the professor verify the circuit. Using the handheld DMM and ELVIS DMM (if you are using ELVIS), measure each resistor value and the total resistance. Record the values in the table below. Compare the measurements and verify that they are within acceptable range.